Boat & Engine Lubricants/Cleaners
Motor Support / Transom Savers
Outboard Engine Flush
Drop Down Plates
Hydraulic Jack Plates
Manual Jack Plates
Outboard Jet Jack Plates & Vertical Extensions
Kick-Up Jack Plates
Manual Kick-Up Jack Plates
Hydraulic Kick-Up Jack Plates
Power Poles & Accessories
Power Pole Manual Jack Plate Mounting Adapters
Power Pole Motor Mount Hydraulic Jack Plate Mounting Adapters
Power Pole Anchor Accessories
Stainless Steel Bolts / Hardware & Marine Silicone
1/2'' Diameter Bolt Kits for Jack Plates (Compatible with all models except minis!)
3/8'' Diameter Bolt kits for Mini Jack Plates (JPL2410SB, JPL2412SB, JPL2710SB, JPL2712SB
Transom Plates & Mounting Templates
Transom Wedges and Spacers
Why a Jack Plate & FAQ's?
Nav Menu 2
Nav Menu 3
Nav Menu 4
Nav Menu 5
Nav Menu 6
Nav Menu 7
Nav Menu 8
Manual Jack Plates
40 - 150 Horse Power
JPL4000 6'' Setback Adjustable Outboard Boat Jack Plate
Quantity in Stock:87
Usually Ships in 24 Hours
Clamp-On Engine Bracket Adapter:
No, I do not have a clamp-on engine and do not need.
Yes, I need the adapter plate for clamp-on engines. [Add $60.00]
Black Powder Coat [Add $80.00]
Clear Anodize [Add $80.00]
Hard Black Anodize [Add $80.00]
Raw Aluminum Finish
Marine Silicone for Installation:
10.1 Oz Tube Marine Silicone [Add $20.49]
2.8 Oz Marine Silicone [Add $12.93]
No, I don't need Marine Silicone
Mounting Bolts(Engine to JackPlate):
Add 2.5'' stainless kit [Add $13.98]
No, I do not need Mounting Bolts.
This Jack Plate is designed for smaller motors to improve the performance of your boat. Two pairs of precision machined aluminum angles locate the motor with 6" setback from the transom. Slots in the angles allow 4" of vertical movement to position the motor in the correct location for maximum output. Stainless steel bolts hold the angles in place. This Jack Plate is rated for motors up to 150 hp and comes in an attractive polished aluminum finish. Fits all V-4 and V-6 standard bolt pattern engines. Some special drilling of holes may be required on engines manufactured before 1980, the pre-drilled bolt pattern is listed below. This unit is new in the box and comes with free technical support and the manufactures full warranty. Cost 30% less than from a Dealer!
Made of high strength polished Aircraft Quality Aluminum
Offers 4 inches of adjustable Vertical movement
6 inches of setback
Weighs 20 lbs
150 Maximum Horsepower
1 Year Unconditional Warranty against manufacturer defects
Jack Plates are the perfect solution for long shaft engines with a short shaft transom! The engine side holes of the Jack Plate is drilled 1.500 inches higher than the transom side. Combined with the 4 inches of adjustable vertical lift you can obtain 5.500 inches at a maximum height to raise your long shaft engine and make it workable on a short shaft transom boat!
Here are the pre-drilled hole dimensions listed below in inches:
Pre-drilled holes for 1/2'' stainless hardware
12 7/8'' across the top two holes from center to center
9 7/8'' across the bottom two holes from center to center
8'' of vertical distance between the top holes and bottom mounting holes
If your holes do not match this configuration, you can drill into the aluminum plate. However, by modifying the unit returns will not be accepted.
We manufacture all of our Jack Plates on our own equipment at our facility in Taft, TN!
If you have any questions please feel free to email or call us, we want to help you. If we are not here or the line is busy, leave a message with your contact information and we will get back with you as soon as possible!
Write a review »
0 of 0 people found the following review helpful:
Ridiculously fast shipping.
August 13, 2019
Reviewer: Patrick Costs from Woodlawn, IL United States
Was this review helpful to you?
Chat with us
, powered by