Boat & Engine Lubricants/Cleaners
Drop Down Plate
Motor Support / Transom Savers
Hydraulic Jack Plates
Hydraulic Kick-Up Jack Plates
Hydraulic Jack Plate Accessories
Manual Kick-Up Jack Plates
Manual Jack Plates
0 - 20 Horse Power
0 - 40 Horse Power
40 - 150 Horse Power
40 - 225 Horse Power
225 - 300 Horse Power
225 - 400 Horse Power
Power Poles & Accessories
Power Pole Manual Jack Plate Mounting Adapters
Power Pole Motor Mount Hydraulic Jack Plate Mounting Adapters
Power Pole Anchor Accessories
Stainless Steel Bolts / Hardware & Marine Silicone
1/2'' Diameter Bolt Kits for Jack Plates (Compatible with all models except minis!)
3/8'' Diameter Bolt kits for Mini Jack Plates (JPL2410SB, JPL2412SB, JPL2710SB, JPL2712SB
Transom Plates & Mounting Templates
Transom Wedges and Spacers
Why a Jack Plate & FAQ's?
Nav Menu 2
Nav Menu 3
Nav Menu 4
Nav Menu 5
Nav Menu 6
Nav Menu 7
Nav Menu 8
Manual Kick-Up Jack Plates
JPL9650 GEN/3 6'' Setback "Kick-Up Plate"
Quantity in Stock:97
Usually Ships in 24 Hours
Clamp-On Engine Bracket Adapter:
No, I do not have a clamp-on engine and do not need.
Yes, I need the adapter plate for clamp-on engines. [Add $60.00]
Clear Anodize [Add $50.00]
Hard Black Anodize [Add $50.00]
Raw Aluminum / No Finish
Marine Silicone for Installation:
10.1 Oz Tube Marine Silicone [Add $19.99]
2.8 Oz Marine Silicone [Add $12.55]
No, I don't need Marine Silicone
Mounting Bolts(Engine to JackPlate):
Add 2.5'' stainless kit [Add $13.19]
No, I do not need Mounting Bolts.
Dimensions: 13'' Height, 6'' Setback, 1/2'' Thick Aluminum
Total weight: 24 pounds
Simply the best idea ever for the adventurous sportsman! This plate allows access to the previously unreachable fishing or hunting ground with a standard tiller engine without worries of prop damage.
Here's how it works:
The jack plate is designed to swivel on the rugged stainless steel shaft in case of an obstacle such as a stump or rock while carefully trolling back to the hotspots your buddies can't reach!
Simply tighten the side swivels to desired setting for your rig size and you are protected from a potential lower unit or prop BOO-BOO! Also included are two safety cables to prevent over-travel swiveling of engine when an obstruction is encountered.
Tightness is determined by engine reverse requirement. The larger the engine, the tighter the swivels for preventing flip-up during reverse.
This is the only Kick-Up plate manufactured by any manufacturer that has vertical travel similar to a jackplate as well as the kick up function limited by stainless steel chain in the event of hitting a log, stump or earth below.
No springs to break and no replacement parts necessary as the JPL9650 is made of aircraft quality aluminum and 3/8 stainless steel chain, grade 316.
CLAMP ON ENGINES:
This unit is compatible with clamp on engines by adding the accessory star-board plate. If you have a clamp-on engine that is not standard BIA Bolt pattern and wish to use this unit, in the options tab add the star-board plate for clamp on engines and it will come installed on the unit so you can use your clamps and have a solid mounting surface. The starboard plate adds 5 more pounds to the weight of the item. The plate is made from marine grade plastic that is resistant to freezing, corrosion, and rot. It is 1 inch thick and spans across the entire mounting surface so that you have plenty of room to mount your engine.
Trailer Your boat:
Locking pins and similar are not necessary for your Vance Manufacturing Kick-Up unit to trailer your boat. Click
for more information and instructions on how to your boat with your new Vance Manufacturing Kick-Up Plate.
Here are the pre-drilled hole dimensions listed below in inches for standard outboard engines:
Pre-drilled holes for 1/2'' stainless hardware
12 7/8'' across the top two holes from center to center
9 7/8'' across the bottom two holes from center to center
8'' of vertical distance between the top holes and bottom mounting holes
If your holes do not match this configuration, you can drill into the aluminum plate. However, by modifying the unit returns will not be accepted.
If you have any questions please feel free to email or call us.
If we are not here or the line is busy, leave a message with your contact information and we will get back with you as soon as possible!
We sell world-wide, give our units a try and put them to work for you!
From everyone at Vance Manufacturing,
for looking and we look forward to serving you!!
WARNING: The JPL9650 Gen/3 is rated for outboard motors up to a maximum of 150 H.P. Do not encounter obstructions at speeds over 5 M.P.H and only in the forward direction. The JPL9650 Gen/3 is not designed to encounter obstructions while the boat is being operated in the reverse direction.
CMC Breakaway, jackplate, jack plate, bobs machine, breakaway plate, motor saver, Vance Manufacturing, CMC Breakaway plate, Breakaway Jackplate
JPL9638 Gen/3 6'' Setback "Kick-Up Plate"
Share your knowledge of this product.
Be the first to write a review »
Chat with us
, powered by