Boat & Engine Lubricants/Cleaners
Motor Support / Transom Savers
Outboard Engine Flush
Drop Down Plates
Hydraulic Jack Plates
Manual Jack Plates
Outboard Jet Jack Plates & Vertical Extensions
Kick-Up Jack Plates
Manual Kick-Up Jack Plates
Hydraulic Kick-Up Jack Plates
Power Poles & Accessories
Power Pole Manual Jack Plate Mounting Adapters
Power Pole Motor Mount Hydraulic Jack Plate Mounting Adapters
Power Pole Anchor Accessories
Stainless Steel Bolts / Hardware & Marine Silicone
1/2'' Diameter Bolt Kits for Jack Plates (Compatible with all models except minis!)
3/8'' Diameter Bolt kits for Mini Jack Plates (JPL2410SB, JPL2412SB, JPL2710SB, JPL2712SB
Transom Plates & Mounting Templates
Transom Wedges and Spacers
Jack Plate FAQs
Shallow Water Fishing in Texas
Jack Plate FAQs
Nav Menu 2
Nav Menu 3
Nav Menu 4
Nav Menu 5
Nav Menu 6
Nav Menu 7
Nav Menu 8
Drop Down Plates
DDPL-001 Static Drop Down Plate Variable Setback
Quantity in Stock:94
Usually Ships in 24 Hours
Clear Anodize [Add $100.00]
Hard Black Anodize [Add $100.00]
Raw Aluminum / No Finish
How much Setback?:
Marine Silicone for Installation:
10.1 Oz Tube Marine Silicone [Add $20.49]
2.8 Oz Marine Silicone [Add $12.93]
No, I don't need Marine Silicone
Mounting Bolts(Engine to JackPlate):
Add 2.5'' stainless kit [Add $13.98]
No, I do not need Mounting Bolts.
Pictures coming soon!
If you have a 90HP - 400HP short shaft engine and a long shaft transom and need to lower your engine, this is the product for your setup! The DDPL-001 Can lower your engine up to 5 inches. This unit is not adjustable, there are multiple holes on the engine and transom side so that you can obtain the correct height while you are installing the engine. If you must adjust after initial installation you will have to remove the engine and move to the desired mounting hole set. This unit is variable setback meaning if you order it with 8 inches of setback and later decide you need 10 inches of setback for clearance issues you may be having, just let us know and we have the extension parts available to you can extend it further out without having to return the unit you have. Before ordering this unit, keep in mind that lowering an engine may cause issues with the engine head hitting the transom when you want to tilt up or hydraulic steering lines/cables may hit the transom. The more setback you have, the less of a possibility you will have clearance issues. This unit is available in a 8'', 10'', 12'' setback.
Overall Dimensions: TBD
Transom side Dimensions: TBD
5'' of vertical drop maximum - Fixes the problem of short shaft engine on long shaft transom
Angles are 1/2'' aircraft aluminum
400 HP Maximum Rating
Hard-Anodized Black Finish Available (Salt Water Ready)
1 Year Limited Warranty against Manufacturer defects
Weighs 50 pounds
Proudly machined and assembled at our own factory in TENNESSEE, U.S.A.!
Drop Down Plates are the perfect solution for short shaft engines with a long shaft transom!
Here are the pre-drilled hole dimensions listed below in inches:
Pre-drilled holes for 1/2'' stainless hardware
12 7/8'' across the top two holes from center to center
9 7/8'' across the bottom two holes from center to center
8'' of vertical distance between the top holes and bottom mounting holes
If your holes do not match this configuration, you can drill into the aluminum plate. However, by modifying the unit returns will not be accepted.
We manufacture all of our products on our own equipment at our facility in Taft, TN!
If you have any questions please feel free to email or call us, we want to help you. If we are not here or the line is busy, leave a message with your contact information and we will get back with you as soon as possible!
DDPL6375 6'' Setback Drop Down Plate
Share your knowledge of this product.
Be the first to write a review »
Chat with us
, powered by