Home > Shop/View Products > Jack Plates > Manual Jack Plates > 0 - 40 Horse Power >

Vance JPL2412SB 5'' Setback Mini-Jack Plate for Gheenoe and Clamp-on Engines

5inch setback mini jack plate


 
Alternative Views:


Our Price: $199.99

Quantity in Stock:7
Availability:: Usually Ships in 24 Hours
Product Code: JPL2412SB


Finish Type:


Mounting Hardware:


Jack Plate Clamping Board Thickness:


Mini Transom Plates Inside Braces:


Marine Silicone for Installation:


Qty:  
Description
 
The JPL2412SB is a miniature single-adjusting jacking plate developed for smaller tiller type outboard clamp-on style engine designs. It is capable of vertically lifting outboard 3” with an offset of 5” from transom. The engine side is 2'' higher than the transom so you can get a total of 5'' of lift if you lift the unit's adjustment to Maximum height. If you want to stay the same height when you install, simply mount the unit a little lower on your transom. The unique ability to adjust vertically sets this unit apart from other style plates. The jack plate has a footprint of 12”x 8” with a 1-1/4” thick clamping surface for all clamp on style outboard engines. With a weight of only 13 lbs the JPL2412SB is capable of handling 0 to 40 HP motors. If your engine is the standard bolt pattern, this unit will not work for your engine.

Please contact Vance Manufacturing for help if your engine is 40 HP & below and your engine has this standard bolt pattern listed below in inches:

  • Pre-drilled holes for 1/2'' stainless hardware
  • 12 7/8'' across the top two holes from center to center
  • 9 7/8'' across the bottom two holes from center to center
  • 8'' of vertical distance between the top holes and bottom mounting holes

The JPL2412SB is constructed of high-strength aircraft quality aluminum and non-rusting hardware consisting of stainless steel, brass, and bearing bronze. The mounting surface plate is made of space-age polymer material known as Starboard which is stronger than marine grade plywood yet will never deteriorate. Starboard will not absorb water therefore it is not subject to rupture from freezing.

Not sure what size thickness clamping plate you need? Measure the minimum distance your outboard engine will clamp and then round up to the nearest inch so you have enough for clamping your engine onto your new Vance Mini Jack Plate. We offer these units with 1 inch, 2 inch, and 3 inch thick mounting plates.

Not sure what size Bolt Kit you need to mount your Vance mini jack plate to your boat transom? Click here to use our mini jack plate bolt kit calculator.


Not sure what a Vance mini transom plate is? Click here for more info.


Not sure which Vance Coating option to choose? Click here for more info.

Average Rating: Average Rating: 5 of 5 5 of 5 Total Reviews: 24 Write a review »

  0 of 0 people found the following review helpful:
 
5 of 5 Jake plate May 2, 2021
Reviewer: steven yeager from cookeville, TN United States  
Excellent value on a awesome piece of workmanship. Easy to install. Thank you

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Nice work April 17, 2021
Reviewer: Jim from Arizona from Parks, AZ United States  
I am an amatuer machinist, with a 1.5 hp mill, and a 2 hp lathe. There is no way I could have done the work evident in this part in my own shop. Very nice, very clean, very professional. Shipping was exactly as advertised. I would buy from Vance again.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Excellent Product April 6, 2021
Reviewer: Anonymous Person from Lansing, NC United States  
Very well machined and finished.  Quality product.  The only issue that I have is that the predrilled holes did not match my Mercury outboard mounting bolts.  When I drilled the plate, the holes were very close to the predrilled holes.  Would be better if there were no predrilled holes.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Excellent quality April 4, 2021
Reviewer: Juan Molina from GRAND ISLAND, NE United States  
So I stumbled apond this product on YouTube and after viewing the product I was unsure because the person was not very adequate about the product. I was definitely interested because it was a good looking product. I found out the name brand of the Jackplate and was on the hunt for more information. I was impressed with the options that I found but still very insecure about purchasing anything. I took measurements and I made sure I had everything in line as far as what I needed for hardware and purchased it and was excited to see the quality of this product. I received the Jakeplate was delivered on time and packaging was excellent.  Thank you very much for taking care of me and I look forward to continuing purchasing more products from this company. The only this I could say negative is that u wish I would have gotten a sticker to put on my jon boat to show people who made this great product for me. Thanks again to all your team!

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Just the right part fair price March 27, 2021
Reviewer: Joseph Puccio from Fort Lawn, SC United States  
Couldn’t find it anywhere but found it here. Very satisfied. Perfect for 25 hp Mercury

Was this review helpful to you?

View All Customer Reviews